Wall display T-slot cutters
T-slot bit
These T-slot cutters will allow you to cut both the groove as well as the wider slot in one pass. A carbide cutting edge is part of the neck of the router bit. The anti-kickback design allows for better performance and reduced vibration under cutting load.
- Designed for creating T-slot wall panels and many other useful purposes.
- Build your own sturdy and attractive slotted wall to display workshop tools –hanging by a hook.
- Cuts all composition materials, hardwoods, plywood and softwoods.
This router bit design is intended for use in router tables and work great in CNC routers. This router bit is not designed for plunging operations.
This router bit has a 12,7 mm shank (shaft) that will fit most large routers. Please ensure that you select a router bit with a shank (shaft) size that will fit into your router collet.
PRO-TECH router bits are manufactured in Taiwan.
| Part No. | _x000D_Shank dia. | _x000D_Cutting width of the slot | _x000D_Cutting width of the groove | _x000D_Cutting Height | _x000D_
| KP10353 | _x000D_1/2 _x000D_ inch | _x000D_28 mm | _x000D_9,5 mm | _x000D_8 mm | _x000D_
_x000D_
_x000D_
 | _x000D_
_x000D_
 | _x000D_
_x000D_
 | _x000D_
|
_x000D_
_x000D_
| consider _x000D_ safety for your health and the people around you | _x000D_|||
_x000D_
General safety suggestions:_x000D_It is advisable to always have the following items nearby and in a good _x000D_ condition _x000D_
| _x000D_
|||
_x000D_
 | _x000D_
_x000D_
 | _x000D_
_x000D_
 | _x000D_
_x000D_
 | _x000D_
| _x000D_
_x000D_
Wear Gloves _x000D_
| _x000D_
_x000D_
_x000D_
Eye Protection _x000D_
| _x000D_
_x000D_
_x000D_
Hearing Protection _x000D_
| _x000D_
_x000D_
_x000D_
Dust Mask _x000D_
| _x000D_
Router Table Safety
_x000D_Although most router bits are small, they can be potentially dangerous and should _x000D_ deserve your attention and respect.
_x000D__x000D_
1 _x000D_
Use push sticks or a push block to position your hands a safe distance from the _x000D_
router bit.
_x000D_ _x000D_ 2 Use large-diameter bits only in a router table. Using bits over 25mm Ø _x000D_ (diameter) in a handheld router can possibly cause you to lose control of the tool _x000D_ and harm yourself or bystanders.
_x000D__x000D_ _x000D_ 3 Always wear a dust mask as well as eye and hearing protection.
_x000D__x000D_ _x000D_ 4 Take light cuts. Heavy cuts invite kickback. If necessary, move the fence _x000D_ closer to the bit or switch to a larger guide bearing/bush.
_x000D__x000D_ _x000D_ 5 Use a featherboard (anti-kickback device) to support the workpiece against _x000D_ the router table and/or fence.
_x000D__x000D_
6 _x000D_
Never climb-cut. Always feed the stock from right to left. Against the rotation _x000D_
of the router bit. (see illustration)
_x000D_ _x000D_ 7 Avoid routing small stock. Instead, rout a larger piece and cut it to size _x000D_ afterwards. If you absolutely have to profile a small piece, build an suitable jig _x000D_ or secure the workpiece.
_x000D__x000D_ _x000D_ 8 Always use a guard. If the fence didn’t come with a guard, make your own.
_x000D__x000D_ _x000D_ 9 Never start the router with the bit in contact with the material.
_x000D__x000D_ _x000D_ 10 Don’t force the router bit or overload the router. Excessive heat is an _x000D_ enemy.
_x000D__x000D_ _x000D_ 11 Secure/fasten the router in the base before starting/switch on the router.
_x000D__x000D_
12 _x000D_
Don’t bottom out the bit in the collet or partially insert the bit. Instead, completely _x000D_
insert the bit, and then back off approximately 2 mm. At least 2/3 _x000D_
's of the router bit shank should be inside the collet.
_x000D_ _x000D_ 13 Be sober and not under the influence of medicine that causes a lack of _x000D_ concentration
_x000D__x000D_ _x000D_ 14 Tidy up your workshop to ensure the ability to move freely with enough _x000D_ room around the router table
_x000D_
