Rabbeting Cutter
For
cutting rebates
Rabbet: (răb′Ät) also re·bate (rē′bÄt′,răb′Ät)
A cut or groove along or near the edge of a piece of wood that allows another piece to fit into it to form a joint.
By choosing alternateive bearings with a larger outside diameter, the depth of cut can be reduced. The cutting height can be increased with multiple passess.
Pupular with picture framers and joinery where a lap joint is required.
Refer to the specification tab for the optonal alternative bearing choices offered by us.
PRO-TECH router bits are manufactured in Taiwan.
Router Bit Maintenance
_x000D_Fortunately, this is pretty easy. The best way to prolong the life of a router _x000D_ bit is to keep it clean. And what you need to do varies with the type of bit._x000D_
_x000D_Note: Sharpening is extremely important too.
_x000D_Bits with Bearings:
_x000D_To clean bits with bearings, first, remove the bearing. Then clean the bit as _x000D_ you did with non-bearing bits.
_x000D_It's important to remove the bearings because even though router bearings are _x000D_ 'sealed,' resin remover can sneak in and dissolve the bearing grease. If this were _x000D_ to happen, you would be faced with the problem of trying to lubricate a sealed bearing._x000D_
_x000D_Despite the claims of bearing grease sellers, we've never had much luck with _x000D_ this. Once that grease is gone, just go buy a new bearing.
_x000D_Bit Shanks:
_x000D_Periodically inspect the shanks of your router bits for rust or burrs. Either _x000D_ of these can be removed quickly with ScotchBrite®. Left on, they can _x000D_ interfere with your ability to properly tighten the bit in the collet.
_x000D_| Part number | _x000D_Cutting width | _x000D_Cutting height | _x000D_Depth | _x000D__x000D_ Shank | _x000D_
| KP3504 | _x000D_1 1/2 inch_x000D_ | _x000D_1/2 inch | _x000D_1/2 inch_x000D_ | _x000D_1/2 inch _x000D_ | _x000D_
| 38.1 mm | _x000D_12.7 mm | _x000D_12.7 mm | _x000D_12.7 mm | _x000D_
Optional bearings to alter the cutting depth
_x000D_| Part number | _x000D_Bearing size | _x000D_
| KP3503-1 | _x000D_5/8 inch OD x 3/16 inch _x000D_ ID | _x000D_
| KP3503-2 | _x000D_3/4 inch OD x 3/16 inch _x000D_ ID | _x000D_
| KP3503-3 | _x000D_7/8 inch OD x 3/16 inch _x000D_ ID | _x000D_
| KP3503-4 | _x000D_1 inch OD x 3/16 inch _x000D_ ID | _x000D_
| KP3503-5 | _x000D_1 1/8 inch OD x 3/16 inch _x000D_ ID | _x000D_
| KP3503-6 | _x000D_1 1/4 inch OD x 3/16 inch _x000D_ ID | _x000D_
* OD = Outside diameter ID = Inside _x000D_
diameter
_x000D_
Length of shank: 38 mm
_x000D_
_x000D_
_x000D_ _x000D_
